Hakutulokset
Hakutulokset
Haulla "1072" löytyi 7 tulosta.
This part of ISO 10724 specifies two two-cavity moulds, designated the type D1 and type D2 ISO moulds, for the injection moulding of small plates measuring 60 mm ´ 60 mm with preferred thicknesses of 1 mm (type D1) or 2 mm (type D2) which can be used for a variety of tests (see annex A). The mou ...
https://sales.sfs.fi/julkaisu.html.stx?id=11697
This part of ISO 10724 specifies the general principles to be followed when injection moulding test specimens of thermosetting powder moulding compounds (PMCs) and gives details of mould designs for preparing one type of specimen for use in establishing reproducible moulding conditions. Its purpo ...
https://sales.sfs.fi/julkaisu.html.stx?id=11696
ISO 10723:2012 specifies a method of determining whether an analytical system for natural gas analysis is fit for purpose. It can be used either to determine a range of gas compositions to which the method can be applied, using a specified calibration gas, while satisfying previously defined crit ...
https://sales.sfs.fi/julkaisu.html.stx?id=234087
This document describes an index test procedure for simulating mechanical damage to geosynthetics, caused by granular material, under repeated loading. The damage is assessed visually and by the loss of tensile strength.
Other reference tests can be used to assess the damage caused by this test. ...
https://sales.sfs.fi/julkaisu.html.stx?id=838993
Method for determination of nitrogen content between 0,0008 % and 0,5 % in steel and iron.
The standards writing body responsible for this document in Finland is Mechanical Engineering and Metals Industry Standardization in Finland.
https://sales.sfs.fi/julkaisu.html.stx?id=11693
This document specifies two methods for the determination of specific heat capacity of advanced monolithic technical ceramic materials based on drop calorimetry (Method A) and differential scanning calorimetry (DSC, Method B) over a temperature range from room temperature upwards, depending on th ...
https://sales.sfs.fi/julkaisu.html.stx?id=11072
Soveltamisala
Tämä standardi koskee irtolaippoja, joita käytetään kauluksien kanssa kestomuovisten paineputkien laippaliitoksiin. Tämän standardin mukaisia laippoja voidaan käyttää standardien SFS 2332, SFS 2336, SFS 3425, SFS 3451, SFS 3461 ja
SFS 4231 mukaisten paineputkien liitoksiin ...
https://sales.sfs.fi/julkaisu.html.stx?id=1072
SFS-EN ISO 10724-2:en – Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs). Part 2: Small plates (ISO 10724-2:1998)
Verkkokaupan tuotteet
SFS-EN ISO 10724-1:en – Plastics. Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs). Part 1: General principles and moulding of multipurpose test specimens (ISO 10724-1:1998)
Verkkokaupan tuotteet
SFS-EN ISO 10723:en – Maakaasu. Jatkuvatoimisten analyysijärjestelmien suorituskyvyn arviointi
Verkkokaupan tuotteet
SFS-EN ISO 10722:2019:en – Geosynthetics. Index test procedure for the evaluation of mechanical damage under repeated loading. Damage caused by granular material (laboratory test method) (ISO 10722:2019)
Verkkokaupan tuotteet
SFS-EN ISO 10720:en – Steel and iron. Determination of nitrogen content. Thermal conductimetric method after fusion in a current of inert gas (ISO 10720:1997)
Verkkokaupan tuotteet
SFS-EN 821-3:en – Advanced technical ceramics. Monolithic ceramics. Thermo-physical properties. Part 3: Determination of specific heat capacity
Verkkokaupan tuotteet
SFS 3128:en – Muoviputket. Kestomuovisten paineputkien irtolaipat. Mitat
Verkkokaupan tuotteet