Siirry sisältöön

Hakutulokset

Hakutulokset

Haulla "592" löytyi 59 tulosta.

SFS-EN ISO 11592-1:en – Veneet. Suurimman propulsiokonetehon määritys liikenopeutta käyttämällä. Osa 1: Veneet, joiden runkopituus on alle 8 m

Verkkokaupan tuotteet
ISO 11592-1:2016 specifies the requirements for determination of the maximum propulsion power rating and manoeuvring speed for engine-driven small craft with a length of hull (LH) of less than 8 m (Lh according to ISO 8666). It is not applicable to the following: personal water craft as defined b ...
https://sales.sfs.fi/julkaisu.html.stx?id=405834

SFS-EN ISO 2592:2017:en – Petroleum and related products. Determination of flash and fire points. Cleveland open cup method (ISO 2592:2017)

Verkkokaupan tuotteet
ISO 2592:2017 specifies a procedure for the determination of flash and fire points of petroleum products using the Cleveland open cup apparatus. It is applicable to petroleum products having open cup flash points between 79 °C and 400 °C, except fuel oils which are most commonly tested by the c ...
https://sales.sfs.fi/julkaisu.html.stx?id=547401

SFS-EN ISO 18592:2019:en – Resistance welding. Destructive testing of welds. Method for the fatigue testing of multi-spot-welded specimens (ISO 18592:2019)

Verkkokaupan tuotteet
This document specifies test specimens and procedures for performing constant load amplitude fatigue tests on multi-spot-welded and multi-axial specimens in the thickness range from 0,5 mm to 5 mm at room temperature and a relative humidity of maximum 80 %. The applicability of this document to l ...
https://sales.sfs.fi/julkaisu.html.stx?id=812161

SFS-EN 1592-4:en – Aluminium and aluminium alloys. HF seam welded tubes. Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes

Verkkokaupan tuotteet
This Part of prEN 1592 specifies the tolerances on dimensions and form of square, rectangular and shaped HF seam welded tubes. These tubes are manufactured from flat rolled aluminium alloy strip longitudinally welded in a continuous process by the passage of an electric current across the abuttin ...
https://sales.sfs.fi/julkaisu.html.stx?id=8756

SFS-EN 1592-3:en – Aluminium and aluminium alloys. HF seam welded tubes. Part 3: Tolerances on dimensions and form for circular tubes

Verkkokaupan tuotteet
This part of prEN 1592 specifies the tolerances on dimensions and form of circular HF seam welded tubes with a diameter up to and including 80 mm and a wall thickness up to and including 2,5 mm. These tubes are manufactured from flat rolled aluminium alloy strip longitudinally welded in a continu ...
https://sales.sfs.fi/julkaisu.html.stx?id=8755

SFS-EN 1592-1:en – Aluminium and aluminium alloys. HF seam welded tubes. Part 1: Technical conditions for inspection and delivery

Verkkokaupan tuotteet
This part of EN 1592 specifies the technical conditions for inspection and delivery of HF seam welded aluminium tubes. It is applicable to HF seam welded tubes obtained by forming cold-rolled strips. It is applicable to aluminium tubes produced from uncoated aluminium strip, as well as to tubin ...
https://sales.sfs.fi/julkaisu.html.stx?id=8753

SFS-ISO 16592:en – Microbeam analysis — Electron probe microanalysis — Guidelines for determining the carbon content of steels using a calibration curve method

Verkkokaupan tuotteet
This International Standard gives guidance on a method for the determination of the carbon content in steels containing other alloying elements (less than 1 % to 2 % by mass) using the calibration curve method. It specifies the sample preparation, X-ray detection, establishment of the calibra ...
https://sales.sfs.fi/julkaisu.html.stx?id=201530