Hakutulokset
Hakutulokset
Haulla "1035" löytyi 72 tulosta.
The ISO 10350 series identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obta ...
https://sales.sfs.fi/julkaisu.html.stx?id=628078
ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under ...
https://sales.sfs.fi/julkaisu.html.stx?id=920738
This document specifies a method for the determination of the mass per unit area. It also specifies five methods (Method A to Method E) for the determination of the fibre mass per unit area of moulding compounds and prepregs. The five methods are as follows:
— Method A: Extraction by Soxhlet;
â ...
https://sales.sfs.fi/julkaisu.html.stx?id=930090
This European Standard specifies an inductively coupled plasma optical emission spectrometry routine method for the analysis of unalloyed and low alloyed steels, whose iron content shall be at least 95 %. This standard differs from the similar standard EN 10351:2011 in that it is optimised for th ...
https://sales.sfs.fi/julkaisu.html.stx?id=236644
This document simulates in a qualitative manner mechanical forces and important environmental influences on an adhesive-bonded joint at a metal polymer interfaces it can also be used as a method of checking the surface preparation of substrates, with a limited detection level.
The test is applica ...
https://sales.sfs.fi/julkaisu.html.stx?id=7885
https://sales.sfs.fi/julkaisu.html.stx?id=112091
This European Standard specifies an inductively coupled plasma optical emission spectrometry routine method for the analysis of unalloyed and low alloyed steels, whose iron content shall be at least 95 %.
This method is applicable to the elements listed in Table 1 within the ranges shown.
Table 1 ...
https://sales.sfs.fi/julkaisu.html.stx?id=162912
This European Standard specifies safety requirements for all the phases of the life of a machine listed in 3.11.a of EN 292-1:1991. Moving platen machines are machines used for the processing of animal hides and skins. They are table type processing machines which are equipped with: - vertical ...
https://sales.sfs.fi/julkaisu.html.stx?id=244922
This Technical Report describes a X-ray fluorescence (XRF) spectrometric method for the determination of Si and Al contents in Ferro Silicon materials.
The method is applicable to:
- Si content between 40 and 90 %;
- Al content between 0,5 and 6 %.
The Technical Report specifies the general re ...
https://sales.sfs.fi/julkaisu.html.stx?id=177190
This Technical Report describes an inductively coupled plasma optical emission spectrometric method for the determination of Al, Ti and P contents in Ferro Silicon materials.
The method is applicable to:
- Al content between 0,2 and 2 %;
- Ti content between 0,02 and 0,25 %;
- P content between ...
https://sales.sfs.fi/julkaisu.html.stx?id=177191
SFS-EN ISO 10350-1:2017:en – Plastics. Acquisition and presentation of comparable single-point data. Part 1: Moulding materials (ISO 10350-1:2017)
Verkkokaupan tuotteet
SFS-EN ISO 10350-2:2020:en – Plastics. Acquisition and presentation of comparable single-point data. Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2020)
Verkkokaupan tuotteet
SFS-EN ISO 10352:2020:en – Fibre-reinforced plastics. Moulding compounds and prepregs. Determination of mass per unit area and fibre mass per unit area (ISO 10352:2020)
Verkkokaupan tuotteet
SFS-EN 10355:en – Chemical analysis of ferrous materials. Inductively coupled plasma optical emission spectrometric analysis of unalloyed and low alloyed steels. Determination of Si, Mn, P, Cu, Ni, Cr, Mo and Sn, following dissolution with nitric and sulphuric acids [Routine method]
Verkkokaupan tuotteet
SFS-EN 14444:en – Structural adhesives. Qualitative assessment of durability of bonded assemblies. Wedge rupture test (ISO 10354:1992 modified)
Verkkokaupan tuotteet
SFS-EN 14444/AC:en – Structural adhesives. Qualitative assessment of durability of bonded assemblies. Wedge rupture test (ISO 10354:1992 modified)
Verkkokaupan tuotteet
SFS-EN 10351:en – Chemical analysis of ferrous materials. Inductively coupled plasma optical emission spectrometric analysis of unalloyed and low alloyed steels. Determination of Mn, P, Cu, Ni, Cr, Mo, V, Co, Al (total) and Sn [Routine method]
Verkkokaupan tuotteet
SFS-EN 1035:en – Nahkateollisuuden koneet. Liikkuvalla tasolla varustetut koneet. Turvallisuusvaatimukset
Verkkokaupan tuotteet
CEN/TR 10354:en – Chemical analysis of ferrous materials. Analysis of ferro-silicon. Determination of Si and Al by X-ray fluorescence spectrometry
Verkkokaupan tuotteet
CEN/TR 10353:en – Chemical analysis of ferrous materials. Analysis of ferro-silicon. Determination of Al, Ti and P by inductively coupled plasma optical emission spectrometry
Verkkokaupan tuotteet