Hakutulokset
Hakutulokset
Haulla "219" löytyi 136 tulosta.
ISO 21969:2009 applies to high-pressure flexible connections intended to be connected to cylinders or cylinder bundles with nominal filling pressures up to 25 000 kPa at 15 °C for use with the following medical gases:
oxygen;
nitrous oxide;
air for breathing;
helium;
carbon dioxide;
xenon; ...
https://sales.sfs.fi/julkaisu.html.stx?id=144000
This part of ISO 21940 presents typical configurations of rotors with flexible behaviour in accordance with their characteristics and balancing requirements, describes balancing procedures, specifies methods of assessment of the final state of balance, and establishes guidelines for balance qual ...
https://sales.sfs.fi/julkaisu.html.stx?id=411080
ISO 21952:2012 specifies requirements for classification of wire electrodes, wires and rods for gas shielded metal arc welding and tungsten inert-gas welding of creep-resisting steels, and for their deposits in the as-welded or post-weld heat-treated condition. One wire electrode can be tested an ...
https://sales.sfs.fi/julkaisu.html.stx?id=193912
ISO 21904-3:2018 defines a laboratory method for measuring the welding fume capture efficiency of on-torch extraction systems. The procedure only prescribes a methodology, leaving selection of the test parameters to the user, so that the effect of different variables can be evaluated.
ISO 21904-3 ...
https://sales.sfs.fi/julkaisu.html.stx?id=658624
ISO 21987:2017 specifies requirements and test methods for mounted spectacle lenses relative to the prescription order.
The standards writing body responsible for this document in Finland is General Industry Federation.
https://sales.sfs.fi/julkaisu.html.stx?id=540707
This document specifies the methods of preparation of test specimens and the standard test methods to be used in determining the properties of thermoplastic polyketone moulding and extrusion materials. Requirements for handling test material and/or conditioning both the test material before mould ...
https://sales.sfs.fi/julkaisu.html.stx?id=810133
This document establishes a system of designation for polyketone (PK) moulding and extrusion materials which may be used as the basis for specifications. Polyketone polymer chains are built up from regularly alternating olefinic units and keto groups. The olefinic units shall be randomly distribu ...
https://sales.sfs.fi/julkaisu.html.stx?id=810121
This document specifies a method for testing equipment for the separation of welding fume in order to determine whether its separation efficiency meets specified requirements.
The method specified does not apply to testing of filter cartridges independent of the equipment in which they are intend ...
https://sales.sfs.fi/julkaisu.html.stx?id=871509
This part of ISO 1219 establishes basic elements for symbols. It specifies rules for devising fluid power symbols for use on components and in circuit diagrams.
This part of ISO 1219 is a collective application standard of the ISO 14617 series. In this part of ISO 1219, the symbols are designed i ...
https://sales.sfs.fi/julkaisu.html.stx?id=389014
Standardin ISO 1219 tässä osassa esitetään piirrosmerkkien peruselementit. Siinä annetaan säännöt piirrosmerkkien laatimiseksi hydrauliikan ja pneumatiikan komponenteille ja piirikaavioihin.
Standardin ISO 1219 tämä osa on sovelluspohjainen kooste standardisarjasta ISO 14617. Standardin ...
https://sales.sfs.fi/julkaisu.html.stx?id=388946
SFS-EN ISO 21969:en – Sairaalakaasujärjestelmien kanssa käytettävät taipuisat korkeapaineliitännät
Verkkokaupan tuotteet
SFS-ISO 21940-12:2016:en – Mechanical vibration — Rotor balancing — Part 12: Procedures and tolerances for rotors with flexible behaviour
Verkkokaupan tuotteet
SFS-EN ISO 21952:en – Hitsausaineet. Hitsauslangat, hitsaussauvat ja hitsiaineet kuumalujien terästen kaasukaarihitsaukseen. Luokittelu
Verkkokaupan tuotteet
SFS-EN ISO 21904-3:2018:en – Health and safety in welding and allied processes. Requirements, testing and marking of equipment for air filtration. Part 3: Determination of the capture efficiency of on-torch welding fume extraction devices (ISO 21904-3:2018)
Verkkokaupan tuotteet
SFS-EN ISO 21987:2017:en – Silmälääketiede. Silmälasien linssit
Verkkokaupan tuotteet
SFS-EN ISO 21970-2:2019:en – Plastics. Polyketone (PK) moulding and extrusion materials. Part 2: Preparation of test specimens and determination of properties (ISO 21970-2:2019)
Verkkokaupan tuotteet
SFS-EN ISO 21970-1:2019:en – Plastics. Polyketone (PK) moulding and extrusion materials. Part 1: Designation system and basis for specifications (ISO 21970-1:2019)
Verkkokaupan tuotteet
SFS-EN ISO 21904-2:2020:en – Health and safety in welding and allied processes. Equipment for capture and separation of welding fume. Part 2: Requirements for testing and marking of separation efficiency (ISO 21904-2:2020)
Verkkokaupan tuotteet
SFS-ISO 1219-1:en – Hydrauliset ja pneumaattiset tehonsiirtojärjestelmät ja komponentit. Piirrosmerkit ja piirikaaviot. Osa 1: Piirrosmerkit tavanomaiseen käyttöön ja tietojenkäsittelysovelluksiin
Verkkokaupan tuotteet
SFS-ISO 1219-1 – Hydrauliset ja pneumaattiset tehonsiirtojärjestelmät ja komponentit. Piirrosmerkit ja piirikaaviot. Osa 1: Piirrosmerkit tavanomaiseen käyttöön ja tietojenkäsittelysovelluksiin
Verkkokaupan tuotteet